OwerGrowen
2020-09-30T16:45:16+00:00
出来之后就在摆弄顺便折磨下我的3600，beta 3出来之后晚上把3600搞到CCX1 4350 CCX2 4375 VID 1306，也算是稳定(P95 Inplace Large FFT，10分钟炸了一个线程然后就停了)
Beta3出来之后，作者说LLC不需要手动设置，开Auto就行
可以用Diagnostic模式直接选数据，但我倾向于下面的方法：
1. 关掉CnQ等所有节能设置
2. 进入系统，打开HWINFO，找到CPU Core Voltage (SVI2 TFN)，打开AIDA64跑FPU，同时关注FPU运行过程中SVI2 TFN所示电压值，这个电压是默认状况下CPU自动达到的最高电压，作为之后Reference Voltage，记下填入CTR。
3. 在Reference Frequency里填入一个频率(可以随意，别太高，我的3600填1300/4450)，然后Start，等他找出最适合的频率，记录数值
4. 关掉软件(别保存)，进BIOS，把刚刚记录下来的频率和电压抄进去，重启，然后就可以跑测试了
5. 测试的话就随意了，P95、OCCT、Realbench、AIDA64 FP64RT挨个往上招呼。CTR默认会把通过测试的频率-25，电压+0.006，比较稳定，P95炸线程这件事情见仁见智了。
Beta3出来之后，作者说LLC不需要手动设置，开Auto就行
更新记录 ...
CTR 1.0 Beta 3
The problem with abnormal results in the "DIAGNOSTIC" mode has been completely solved.
New hints in the log.
The tolerances for Vdroop have been revised, LLC status alerts will only be issued if there is only a serious problem with the processor power supply. In most cases LLC Auto will now be enough.
Ryzen 5 3500, Ryzen 5 3500X and Ryzen 9 3900 now fully supported.
Additional protection against non-indigenous input of values.
CTR no blocks the interface, if the operating system contains incorrect CPPC tags or the tags cannot be read.
Additional calibrations in error detection algorithms.
The default temperature threshold has been increased (80->85). CTR will stop all processes if the temperature of 85 degrees is reached.
No results in "BENCHMARK" tab. Fixed.
The problem with abnormal results in the "DIAGNOSTIC" mode has been completely solved.
New hints in the log.
The tolerances for Vdroop have been revised, LLC status alerts will only be issued if there is only a serious problem with the processor power supply. In most cases LLC Auto will now be enough.
Ryzen 5 3500, Ryzen 5 3500X and Ryzen 9 3900 now fully supported.
Additional protection against non-indigenous input of values.
CTR no blocks the interface, if the operating system contains incorrect CPPC tags or the tags cannot be read.
Additional calibrations in error detection algorithms.
The default temperature threshold has been increased (80->85). CTR will stop all processes if the temperature of 85 degrees is reached.
No results in "BENCHMARK" tab. Fixed.
可以用Diagnostic模式直接选数据，但我倾向于下面的方法：
1. 关掉CnQ等所有节能设置
2. 进入系统，打开HWINFO，找到CPU Core Voltage (SVI2 TFN)，打开AIDA64跑FPU，同时关注FPU运行过程中SVI2 TFN所示电压值，这个电压是默认状况下CPU自动达到的最高电压，作为之后Reference Voltage，记下填入CTR。
3. 在Reference Frequency里填入一个频率(可以随意，别太高，我的3600填1300/4450)，然后Start，等他找出最适合的频率，记录数值
4. 关掉软件(别保存)，进BIOS，把刚刚记录下来的频率和电压抄进去，重启，然后就可以跑测试了
5. 测试的话就随意了，P95、OCCT、Realbench、AIDA64 FP64RT挨个往上招呼。CTR默认会把通过测试的频率-25，电压+0.006，比较稳定，P95炸线程这件事情见仁见智了。