[拼装] [技术交流] 亿辉 1/35 Z高达胸像完成

各位好,因为最近PGU初钢抢都抢不到,然後看着一堆开箱觉得心痒也想
弄个大东西来做看看

然後又看到之前亿辉胸像(新安洲)所以找了Z高达的来做
(如果PGU出了Z必买,uc最喜欢的一台主角机)


所以 [s:ac:哭笑]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-7bxkK19T1kSf0-qo.jpg[/img]


盒子真的够大,里面是完全塞满的



之後慢慢开始从头组
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-gkbqZaT3cSsg-rc.jpg[/img]

光是头就很大了,很有重量感

之後开始上色,想弄成Z3配色
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-fw2iK1zT3cSsg-ow.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-hep2K27T3cSsg-qx.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-l69yK2eT3cSsg-lp.jpg[/img]


灰色都是用黑白补土调整,比例是随意,紫色都是红底成形色上洋红加紫色薄喷


然後开始组身体,里面的发光框架含开关
里面配线蛮难塞的,很多地方都大手大脚的硬塞进去

装好居然真的会发亮
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-8e8qK1rT1kSf0-qo.jpg[/img]


之後弄好身体
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-f7hiZbT3cSsg-om.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-kfqeK2kT3cSsg-mh.jpg[/img]

测试开灯
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-feehK20T3cSsg-rz.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-fyy5K1dT3cSsg-ky.jpg[/img]


之後弄好肩膀背包
不过背包好像不会亮了,不知道出了啥问题
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-dz03ZbT3cSsg-ok.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-951xZdT3cSrz-sg.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-emtnK1zT3cSsg-qs.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-3d53ZaT3cSsg-qq.jpg[/img]

接着是肩膀的A标志,本来想说肩膀有做裂甲,很难切割
然後本来那样看起来又还不错的感觉本来不想喷的

但後来觉得这个关卡如果没跨过又好像会失去了甚麽 [s:ac:愁]



所以就开始喷了

先贴遮盖胶带,早知道应该买宽一点的,重叠的部分真的很难割
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-dsicK23T3cSsg-nq.jpg[/img]

切完後开始喷漆,喷漆前一直很担心溢色所以死命注意边缘有没有压好
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-4bc5K2qT3cSsg-na.jpg[/img]


撕掉後感觉还OK,还好没失败
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-39uaZbT3cSsg-r9.jpg[/img]

装好後
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-2cngK2kT3cSsg-nb.jpg[/img]

测试开灯
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-aya9K1mT3cSsg-o4.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-h4hK1aT3cSsg-lk.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-giyyK1iT3cSsg-j1.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-4fv0K13T3cSsg-m9.jpg[/img]


感觉还行


之後就是接着用油彩抹一抹弄一下就完成了

只做了头到身体这边的旧化,後面背包还有底座就弄很少,严重程度从重到轻这样
(其实是弄一弄旧化想到蛮多讨厌的事情所以懒了)
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-ghrkZcT3cSsg-rc.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-im52ZcT3cSsg-pj.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-5kumZbT3cSsg-ov.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-4clkZbT3cSsg-ql.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-dfcbK2sT3cSsg-qn.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-d9yyZbT3cSsg-ql.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-f3ugK2oT3cSsg-nb.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-kcniK26T3cSsg-jl.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-4gx1K2oT3cSsg-lh.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-25hxK2oT3cSsg-k4.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-8j8K2bT3cSsg-jp.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-7je3K2eT3cSsg-iy.jpg[/img]

旁边探照灯的可动机构
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-152oK2aT3cSog-sg.jpg[/img]

[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-1wz6K2jT3cSsg-lc.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-5catK2qT3cSsg-k8.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-gxxnK2lT3cSsg-oe.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-82u8K2kT3cSsg-k1.jpg[/img]

一样开灯试试看
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-1q6uK20T3cSsg-ms.jpg[/img]

光源关更低一点,不然探照灯真的不太亮
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-6js9K1eT3cSsg-lo.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-hhbeK1fT3cSsg-jr.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-36b0K1dT3cSsg-hn.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-5h8bK1kT3cSsg-m6.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-appK1gT3cSsg-k0.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-dnpcK18T3cSsg-m3.jpg[/img]
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-7myrK18T3cSsg-ji.jpg[/img]

不过LED灯的颜色不统一有点可惜,有种太电竞RGB的感觉了



跟其他比例的对比

PG渣古
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-h028ZcT3cSsg-ng.jpg[/img]

MG
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-5w6kZcT3cSsg-oj.jpg[/img]

RG Z3
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-yspZcT3cSsg-s9.jpg[/img]


这是这次总共使用的颜料
[img]https://img.nga.178.com/attachments/mon_202102/01/jwQiza-3kb6ZcT3cSsg-n1.jpg[/img]


比例说大台不是很大,说小又不小

照片就这样了


说实话做的时候蛮痛苦的,水口超大
而且每个框架的脱模剂超级多,零件都是油的那种

素组感觉也不太能看,所以这次就尽量把零件上色後组起来就好

弄了一个多月总算结束了


Z高达真的好帅啊... 不过家里没空间摆了...




最後感谢各位观看的大佬们